If your bed is warped or you are just looking for convenience, a BLtouch is a great upgrade for your 3D printer. This video aims to be a complete guide to all things BLtouch. This ranges from an explanation of auto bed levelling, through to mounting, wiring, firmware, calibration, operation and customisation.
Free companion webpage: https://teachingtechyt.github.io/upgrades.html#bltouch
0:00 Introduction
0:44 What is a BLtouch?
1:46 What to buy?
2:08 Genuine vs clone
2:33 Physical mounting
3:46 Wiring
PWM Wikipedia article: https://en.wikipedia.org/wiki/Pulse-width_modulation
5:35 FAQ: Do I need a pin27 board?
6:12 FAQ: Can I use a custom pin for the yellow wire?
LPC1768 datasheet (SKR V1.3): https://www.nxp.com/docs/en/data-sheet/LPC1769_68_67_66_65_64_63.pdf
6:49 Marlin firmware configuration
Beginner firmware setup guide: https://youtu.be/eq_ygvHF29I
8:26 Calibrating probe offsets
My dedicated video on this: https://youtu.be/fN_ndWvXGBQ
9:02 Basic BLtouch operation
9:43 The two ways to use a BLtouch when printing
10:37 Customisation - Grid points, speed, margins
11:56 Troubleshooting
My dedicated troubleshooting video: https://youtu.be/fiwbp2NKyTY
Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: www.x3d.com.au
Get Quality Resins from 3D Printers Online. 5% off storewide for Teaching Tech subscribers [Code: tech5]
https://3dprintersonline.com.au/
Take a look around and if you like what you see, please subscribe.
Support me on Patreon: http://www.patreon.com/teachingtech
Free companion webpage: https://teachingtechyt.github.io/upgrades.html#bltouch
0:00 Introduction
0:44 What is a BLtouch?
1:46 What to buy?
2:08 Genuine vs clone
2:33 Physical mounting
3:46 Wiring
PWM Wikipedia article: https://en.wikipedia.org/wiki/Pulse-width_modulation
5:35 FAQ: Do I need a pin27 board?
6:12 FAQ: Can I use a custom pin for the yellow wire?
LPC1768 datasheet (SKR V1.3): https://www.nxp.com/docs/en/data-sheet/LPC1769_68_67_66_65_64_63.pdf
6:49 Marlin firmware configuration
Beginner firmware setup guide: https://youtu.be/eq_ygvHF29I
8:26 Calibrating probe offsets
My dedicated video on this: https://youtu.be/fN_ndWvXGBQ
9:02 Basic BLtouch operation
9:43 The two ways to use a BLtouch when printing
10:37 Customisation - Grid points, speed, margins
11:56 Troubleshooting
My dedicated troubleshooting video: https://youtu.be/fiwbp2NKyTY
Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: www.x3d.com.au
Get Quality Resins from 3D Printers Online. 5% off storewide for Teaching Tech subscribers [Code: tech5]
https://3dprintersonline.com.au/
Take a look around and if you like what you see, please subscribe.
Support me on Patreon: http://www.patreon.com/teachingtech
- Категория
- 3D Принтеры
Комментариев нет.