AMAZING DIY Pitts S12 Full Build and Flight

STL Files: https://www.eclipson-airplanes.com/pitts12

LW-PLA: https://colorfabb.com/lw-pla-natural

Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmillanrc

See what else I am working on: https://www.instagram.com/troymcmillan_rc/
#3DPrinted,#RCAirplane, #ItFlies

Pitts S12 Parts:
SunnySky 2820 1100kv Motor: https://sunnyskyusa.com/products/sunnysky-x2820-brushless-motors?variant=45672114511
11x5.5 APC prop: https://amzn.to/3AFIA0V
60A ESC: https://amzn.to/3nwXJw1
ES08MA Servo: https://amzn.to/3ANk2mB
3S 2700mAh Battery:
4S 2200mAh Battery:
2x8mm Screws: https://amzn.to/3p8gmqY
10x5x3 Magnets: https://amzn.to/3bzb4Pz
1/8” Wheel Collar: https://amzn.to/3p4tvl1
3pin wire assortment: https://amzn.to/3l1xNYt
XT60 connector: https://amzn.to/3iyZWnf
2mm push rod ends: https://amzn.to/3nnjD4U

3D Printers I use and recommend:
AnyCubic Vyper: https://amzn.to/3AJqwTM
Artillery Sidewinder 3D Printer: https://amzn.to/396eqIp
Artillery Genius 3D Printer: https://amzn.to/39cA6CZ
Ender3 V2: https://amzn.to/2SmLOGk
Twotrees Sapphire-PRO: https://amzn.to/3wtNOLz
Anycubic Mega X Printer: https://amzn.to/3f4oS89
Fokoos Odin-5: https://amzn.to/3fAES06

3D Printing Filament:
ABS for motor mounts: https://amzn.to/3xgLI2c
ColorFabb LW-PLA: https://colorfabb.com/lw-pla-natural
ePLA-ST: https://amzn.to/3AGymgY
TPU: https://amzn.to/2Sw3Oe8

Tools and Supplies used:
Spektrum DX6 Controller: https://amzn.to/3l6NFsD
Spektrum NX10 Controller: https://amzn.to/3jnjvST
Receiver: https://amzn.to/3j4PbK4
Battery Charger: https://amzn.to/3vejwfL
Charge cable: https://amzn.to/34lOk3q
XT60 connector: https://amzn.to/3iyZWnf
Assortment of 3-Pin Extension Cables: https://amzn.to/3l1xNYt
Z-Bend pliers: https://amzn.to/34mA0rt
2mm push rod ends: https://amzn.to/3nnjD4U
CA Glue: https://amzn.to/2J8EvNW
CA Accelerator: https://amzn.to/3fpbycz
Low-Voltage Tester: https://amzn.to/2Yk0A0w
Hot knife: https://amzn.to/3nrCwUH
Drill Bits: https://amzn.to/3nIJzrx
Hobby Knife: https://amzn.to/3eYOYJq
#11 blades: https://amzn.to/3vTJZ2W
Z-Bend pliers: https://amzn.to/34mA0rt
Build Mat: https://amzn.to/3vJmauw
Onboard Camera: https://amzn.to/3rp2OrH
Lead weight: https://amzn.to/3cFnzeu

Print Settings:

Quality:
Layer Height – 0.25
Initial Layer Height - 0.15
Line Width – 0.4
Walls:
Wall Line Count – 1
Z Seam Alignment - User Specified
Z Seam Position - Back (Position part to align Z seam)
Seam Corner Preference - Expose Seam
Top/Bottom:
Top Layers - 0
Bottom Layers - 0
Infill:
Infill Density – 0
Material:
Printing Temperature – 235
Build Plate Temperature – 60
Flow – 55%
Speed:
Print Speed – 100
Outer Wall Speed – 55
Inner Wall Speed – 55
Travel Speed – 120
Travel:
Enable Retraction – Checked
Retraction Distance – 7.5mm (Bowden Tube Ender3)
Retraction Speed – 35mm/s
Retraction Extra Prime Amount – 0.2
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 80
Mesh Fixes:
Union Overlapping Volumes – Checked
Special Modes:
Surface Mode – Normal
Experimental:
Slicing Tolerance – Middle





Music:

Song: Jarico - Landscape (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: https://youtu.be/EwRdKJURDHw

Music: Joakim Karud:
YouTube: https://youtube.com/joakimkarud
Soundcloud: https://soundcloud.com/joakimkarud

Music provided by Argofox:
From The Dust - Solar
https://youtu.be/dFeNxFmvvA8

Music provided by Argofox:
Ghost'n'Ghost - Lighthouse
https://youtu.be/xVzeZGRZk0s




Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!